Air Gunsa AZ40 HTE AV, Инструкция по эксплуатации

Страница: 2 / 5

6 1
GB
2. SAFETY WARNING
FIRE AND EXPLOSION
1. Never use the following HALOGENATED HYDROCARBON
SOLVENTS:
which can cause cracks or dissolution of gun body (aluminium) due to
chemical reaction. UNSUITABLE SOLVENTS: methyl chloride, dichloro-
methane, 1.2-dichloroethane, carbon tetrachloride, trichloroethylene,
1.1.1-trichloroethane.
2. Sparks and open flames are strictly prohibited. Paints can be highly
flammable and can cause fire. Do not expose to open flames, electrical
goods, cigarettes etc.
3. Securely ground spray gun using conductive air hose. (Less than 1M Ω ).
Always ensure that the spray gun is earthed correctly.
PROTECTION OF HUMAN BODY
1. Use in a well-ventilated site, using a spray booth.
Poor ventilation can cause organic solvent poisoning and fire.
ALWAYS observe WARNINGS and CAUTIONS in this
instruction manual.
1. TECHNICAL SPECIFICATIONS
This AIR GUNSA spray guns kit complies to ATEX regulations 94/9/EC,
protection level:II 2 G X Suitable for using Zones 1 and 2.
X marking: Any static electricity discharge from the spray gun is to be divert-
ed to the ground via the conductive air hose as stipulated.
Before use, adjustment or maintenance, it is important
to read this instruction manual very carefully. This manual
must be stored in a safe place for any future reference.
2. Always wear protective gear (safety glasses, mask, gloves) to avoid
inflammation of eyes and skin. In case of any physical discomfort, imme-
diately seek medical advice.
3. Noise level can exceed 80 dB(A), wear earplugs if necessary.
4. Pulling the trigger many times during operation, may cause carpal
tunnel syndrome. Always rest, in case of tiredness.
IMPROPER USE
1. Never point gun towards people or animals.
2. Never exceed maximum working pressure or maximum operating
temperature.
3. Always release air and fluid pressure before cleaning, disassembling
or servicing, otherwise, remaining pressure can cause bodily injury due
to improper operation or scattering of cleaning liquid.
4. Tip of fluid needle set has a sharp point.
Do not touch the tip during maintenance to avoid accidents.
5. Never use this gun to spray foods or chemicals, otherwise, foreign substan-
ce, could cause corrosion of fluid passages which could adversely affect
health.
6. Never alter this spray gun, to avoid insufficient performance and damage.
7. If something goes wrong, immediately stop operation and find the
cause. Do not use again, until you have solved the problem.
8. Do not enter working areas, where robots, reciprocators, etc. are used,
until they have been turned off.
Otherwise, they could cause injury.
3. HOW TO USE
CAUTION
- Use clean air filtered through air dryer and air filter.
- When using this gun for the first time after purchase, adjust fluid needle
packing (12) with needle packing nut (13), spray cleaner to clean fluid
passages and remove rust preventive oil.
- Firmly fix cup to spray gun, to avoid disconnection of it, that can cau-
se bodily injury.
1. Firmly connect an air hose to air nipple 1/4” (25).
2. Firmly fix gravity cup to fluid nipple (3).
3. Flush fluid passages with a compatible solvent.
4. Pour paint into container, test spray, adjust fluid output and pattern
width.
4. HOW TO OPERATE
_ Suggested atomizing air pressure is 2.0 to 3.0 bar (29 to 44 PSI).
_ Paint viscosity differs according to paint property and painting condi-
tions. 12 to 23 sec. / Ford cup#4 is recommended.
_ Set the spray distance from the gun to the work piece, as near as possi-
ble within the range of 100-200 mm.
_
The gun should be held so that it is perpendicular to the surface of the
workpiece at all times. Then, the gun should move in a straight and hori-
zontal line. Arcing the gun causes uneven painting.
Symbol WARNING Hazard level Consequence
WARNING
Potentially hazardous Death or serious injury
situation
CAUTION
Potentially hazardous Minor to moderate injury
situation
IMPORTANT Potentially hazardous Property damage
situation
* Measuring point: 1m backwards from gun, 1.6m height.
Model Nozzle Air cap Air pressure Fluid* Air Pattern
Orifice set at inlet output consumption width
Ø mark bar ml/min Nl/min mm
AZ40 HTE AV alimentazione a gravità
AZ40 HTE 0.8 0.8 08 60 130 100
AZ40 HTE 1.0 1.0 10 90 130 110
AZ40 HTE 1.2 1.2 12 120 130 130
AZ40 HTE 1.5 1.5 15 170 170 140
AZ40 HTE 1.8 1.8 18 210 200 150
AZ40 HTE 2.0 2.0 20 230 200 160
Fluid nipple: G 1/4”
Air nipple: G 1/4”
Max. working air pressure: 7.0 bar (100 PSI)
Noise level (LAeqT)*: 74.5 dB (A)
Max. Temperature range: 5 ~ 40 °C
Weight g (lbs): without cup 420 (0.92)
Weight g (lbs): with cup 600 cc Cup _570 (1.25) - 200 cc Cup _520 (1.14)
* Paint viscosity: 21 sec./Ford cup # 4.
2.5