Pg. 2
IS-SS-CI Instr.
0413JD
Aiphone Corporation
1700 130th AVE NE * Bellevue, WA 98005
Ph: (800) 692-0200 * Fax: (425) 455-0071
WIRING DIAGRAM:
IS-SS-CI
IS-CCU
IS-MV
IS-PU-UL
CAT-5e
CAT-5e
FCC WARNING:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.
•
For proper regulatory compliance, the drain wire should be disconnected at the power
supply end of the cable.
•
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
E-MAIL: [email protected]
SPECIFICATIONS:
Terminations:
RJ45 jack for audio/video
Screw terminals for door release and relay outputs
Relay rating:
24V AC/DC 0.5A on Door station, 24V AC/DC 1.0A on relay board
Camera Input:
Analog NTSC 1Vpp
Operating Temp:
14° ~ 140°F / -10° ~ 60°C
Wiring Distance:
980’ with Cat5e/6 cable
Dimensions:
11-3/4” H x 7” W
w/SBX-ISDVFRA:
11-11/16” H x 7-1/16” W x 2-13/16” D (top), 1-13/16” D (bottom)
OFF ON
NO
NO
C
NC
C
NC
1234
OFF ON
NO
NO
C
NC
C
NC
1234
Board on back of unit
See wiring below
RELAY BOARD WIRING AND SETTINGS:
CCTV Input
CCTV Output
Relay 1 Output
N/O, COM, N/C
Relay 2 Output
N/O, COM, N/C
For door release
1.0 Amp contact
*75Ω termination
for CCTV output
* Unit is shipped with the pin connector set to the ON
position. Change pin connector to the OFF position to
loop video from the CCTV output.
Configuration Switch
See Settings to right
ON
1
2
3
4
Default Configuration when shipped
Optional Configurations
ON
1
2
3
4
Normal Call
Emergency Call
Talking
Door Release
Trigger Source RY1 Triggered?
RY1 Remains ON
During Talking?
RY2 Triggered?
RY2 Remains ON
During Talking?
RY2 Requires
Reset?
YES
NO
N/A
YES
NO
N/A
N/A
NO
N/A
YES
YES
YES
YES
YES
YES
N/A
N/A
N/A
NO
NO
Contact Technical Support if additional switch configurations
are required.
Normal Call
Emergency Call
Talking
Door Release
Trigger Source RY1 Triggered?
RY1 Remains ON
During Talking?
RY2 Triggered?
RY2 Remains ON
During Talking?
RY2 Requires
Reset?
YES
NO
N/A
YES
YES
YES
YES
**
NO
NO
NO
NO
NO
N/A
N/A
N/A
N/A
YES
YES
NO
NO
**Connected to door
release output
of door station
when shipped
Relay 1 triggers on normal call, emergency call, and communication. Relay 1 remains on during communication.
Relay 2 triggers when the door release button of the master is pressed. Use this configuration if you need a larger
relay contact than the 0.5 Amp supplied from the door station.
Relay 1 triggers on normal call, emergency call, and communication. Relay 1 remains on during communication.
Relay 2 triggers on communication and remains on during communication.
*
* Connect to the IS-CCU or IS-SCU and
program as a video door station, even if no
CCTV camera is connected.
ON
1
2
3
4
Normal Call
Emergency Call
Talking
Door Release
Trigger Source RY1 Triggered?
RY1 Remains ON
During Talking?
RY2 Triggered?
RY2 Remains ON
During Talking?
RY2 Requires
Reset?
YES
NO
N/A
YES
NO
N/A
N/A
NO
N/A
YES
YES
YES
YES
YES
YES
N/A
N/A
N/A
NO
NO
***Option Input
Any N/O dry contact
can be used.
*** Relay 1 triggers on normal call and communication. Relay 1 remains on during communication. Relay 2 triggers
when option input is triggered and remains on during communication.
If using this configuration Relay 2 can not be used for door release. You must wire directly from the door station
relay output for door release and disconnect the Red/Bown wires that are currently wired to the door station relay.
4-pin connector
