Aim PDM 32 Скачать руководство пользователя | Manualshive

Страница: 43 / 63

background image

www.aim-sportline.com

- PDM 32 User Guide

42

16.

Display configuration

The PDM 32 may manage two different displays:

The 6” and the 10”.

You have to select which display you wish to connect through the proper software page:

Then you may proceed with the display configuration, in order to have a maximum of 8 pages available.

«
...
41
42
43
44
45
...
»

Содержание PDM 32
































































Отзывы:

Нет отзывов

Похожие инструкции для PDM 32

Бренд: SmartPower Страницы: 4

Бренд: ICM Controls Страницы: 2

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: D&R ELECTRONICS Страницы: 16

Бренд: CommScope Страницы: 45

Бренд: AC Infinity Страницы: 16

Бренд: Noark Страницы: 4

Бренд: Zero88 Страницы: 12

Бренд: JEAN MÜLLER Страницы: 20

Бренд: Panamax Страницы: 2

RELION 650 SERIES

Бренд: ABB Страницы: 68

Бренд: Sel Страницы: 52

APS POWERVERTER

Бренд: Tripp Lite Страницы: 40

Бренд: JUICE GOOSE Страницы: 4

Бренд: JUICE GOOSE Страницы: 6

Бренд: Beckhoff Страницы: 64

Бренд: Beckhoff Страницы: 113

ESP Next Gen PCS

Бренд: Ametek Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды