Aim-TTI QL Series II Скачать руководство пользователя страница 21

Страница: 21 / 42

# Code

Function

Main Output always off at power-up (factory default)

Main Output status at power-up the same as at last power-down

Aux Output (T models only) always off at power up (factory default).
Set with control assigned to Output 1.

Aux Output (T models only) status at power up the same as at last power down.
Set with control assigned to Output 1.

Alarm output 'open' for main Output off, 'closed' for main Output on

Alarm output 'closed' when Aux Output is in Current Limit.
Set with control assigned to Output 1; applies to Output 1 alarm only.

Alarm output 'closed' when over-temperature trip occurs

Alarm output 'closed' when sense trip occurs

Alarm output 'closed' when over-current trip occurs

Alarm output 'closed' when over-voltage trip occurs

Alarm output 'closed' when any trip occurs (factory default)

Buzzer off

Buzzer on (factory default). A single beep indicates confirmation, a double beep
indicates a wrong entry.

Lock/Unlock settings. Note that the AUX output settings are locked with Output1.

Jog digit flashes, JOG indicator only flashes when jog is 'hidden'

JOG indicator always flashes, except when 'hidden' (factory default)

JOG indicator doesn't flash, except when 'hidden' (lazy flash)

Loads default calibration parameters. Refer to Service Guide

Shows firmware version number in the display

Sets these # settings to their factory default

Loads Factory Default settings (see below)

Clears all the output’s set-up memories. AUX output always cleared with O/P1.
In LINK mode, clears all memories in all modes (O/P1, O/P2, AUX & LINK).

Enter calibration mode. Refer to Service Guide.

Factory Default Settings

The ex-factory default settings (which will apply at first power-up) are as follows:

Range:

QL355: 35V/3A

QL564: 56V/2A

Voltage:

QL355: 1.000V

QL564: 1.000V

Current Limit:

QL355: 1.000A

QL564: 1.000A

OVP:

QL355: 40V

QL564: 60V

OCP:

QL355: 5.5A

QL564: 4.4A

Output:

Output off; local Sense

# Settings:

Main Output always off at power-up

Aux Output always off at power up (an Output 1 # function only).

Alarm output 'closed' when any trip condition occurs

Buzzer on

JOG indicator always flashes; 'lazy' flash when hidden

Содержание QL Series II











































Результаты поиска

Содержание QL Series II

Отзывы:

Похожие инструкции для QL Series II

Бренды по названию

Популярные бренды

Aim-TTI QL Series II, Инструкция по эксплуатации

Результаты поиска

Содержание QL Series II

Отзывы:

Похожие инструкции для QL Series II

Бренды по названию

Популярные бренды