manualshive.com logo in svg

AIC Nesta N 120 FS, Руководство по установке и обслуживанию, Страница: 52 / 72

Поделиться
Скачать
AIC Nesta N 120 FS Скачать руководство пользователя страница 52

Fig. 21. Cleaning the Combustion Chamber

I-52

A-070336_EN • Rev. A

M

aintenance

Checking and Cleaning the Combustion 

Chamber

Conditions:

 

î

Burner removed, see 

“Removing and Install-

ing the Burner” on page I-51.

Tools and material:

 

î

Industrial vacuum cleaner

 

î

Nylon bristle brush

 

î

Torch lamp

Check Procedure:

These procedures should be per-

formed  through  the  burner  open

-

ing. Do not remove the burner 

plate, as it could damage the seals 

and insulation.

1. 

Using a torch lamp, visually check the condi-

tion of the combustion chamber. If it is dirty, 

clean it.

OFF

Cleaning Procedure

1. 

Using a nylon bristle brush, sweep the walls 

of the combustion chamber.

2. 

Using an industrial vacuum cleaner, remove 

all deposits from the combustion chamber 

heating surfaces.

Follow-on tasks:

3. 

Install the burner, see 

“Removing and In-

stalling the Burner” on page I-51.

Содержание Nesta N 120 FS









































































Отзывы:

Нет отзывов