manualshive.com logo in svg

Agria 8200-V4, Руководство по эксплуатации

Поделиться
Скачать
Agria 8200-V4 Скачать руководство пользователя страница 11

Edition 09.98

Verticutter 8200-V4

11

1. Safety Instructions

1

Engine, Fuel, and Oil

Never let the engine run in closed rooms.
Extreme danger of intoxication!

Careful when dealing with fuel. Great
danger of fire!

Never refill fuel close to open fire, inflam-
mable sparks or hot engine parts. Do not
refill fuel in closed rooms. Do not smoke
when refilling!

Refill only with the engine switched off
and cooled down.

Do not spill any fuel, use a proper filling
device.

In case of fuel-spillage, push the
verticutter away from the spillage before
you start the engine.

Ensure the fuel is of required quality.

Store fuel in approved cans only.

Store anti-corrosive agents and stabiliz-
ing liquids out of reach of children. If
sickness and vomiting occur, see a doc-
tor. If fuel has contacted eyes, rinse them
thoroughly, avoid inhaling of vapours.

Read and observe enclosed instructions.

Before you dispose of opened and seem-
ingly empty pressurised tins (e.g. of
assist-starting liquids) make sure they
are completely empty. Empty them in
ventilated places safe from spark forma-
tion or flames. If necessary, dispose of
tins in hazardous waste deposits.

Be careful when draining hot oil – danger
of burns.

Ensure the oil is of required quality. Stor-
age is in approved cans only.

Dispose of oil, greases, and filters sepa-
rately and properly.

Electrical System

Persons having a pacemaker must not
touch live parts of the ignition system
when the engine is running.

Explanation of Warning
Symbols

Before doing any
cleaning, mainte-
nance and repair
work, shut off the en-
gine and remove
spark plug connec-
tor.

Keep off the knives
while the engine is
running!

Do not touch rotating
machine parts. Wait
until they have come
to a complete stop.

Do not operate the
machine without
guards! Move guards
in place before you
take up operation.

Содержание 8200-V4









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды