Agria 5100 Rabbit Скачать руководство пользователя страница 28

Страница: 28 / 48

agria

Grassland Mower 5100

5. Maintenance

Locking bolts on steering handle

To ensure the steering handle moves easily when ad-
justed to the side:

Apply some bio-lubricating oil through the hole at

least once per year or after cleaning the machine with
the pressure washer.

Apply some bio-lubricating oil to the bearing on the

mowing drive clutch lever (B/4) through the hole at
least once per year or after cleaning the machine with
the pressure washer.

Drive-wheels

Check the tyre pressure periodically. In particular,

ensure that both tyres have equal pressures to give
smooth riding.

Attach the wheels with the pointed part of tread

lugs showing in travel direction (seen from above) to
obtain full traction.

Watch the wheel shaft for grass winding

around it and remove the grass, if neces-
sary, by removing the wheels.

Wheel Shaft

Apply bio-lubricating grease to the wheel
shaft around the hub each time the ma-
chine was cleaned with a pressure washer
or at least once per year.

Mowing Attachment

The cutter bar is exposed to extreme strain. There-
fore, it evidently must be maintained and adjusted with
special care.

Each time before you take up operation and at

intervals of 8 operating hours, lubricate all gliding parts
with bio-lubricating grease or bio-lubricating oil.

At intervals of approximately 30 minutes of opera-

tion re-tighten all nuts and bolts on the mowing drive
and cutter bar (especially on the knife driver).

Содержание 5100 Rabbit

















































Результаты поиска

Содержание 5100 Rabbit

Отзывы:

Бренды по названию

Популярные бренды

Agria 5100 Rabbit, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 5100 Rabbit

Отзывы:

Бренды по названию

Популярные бренды