background image

6

CAUTION: EYE PROTECTION SHOULD 
BE WORN WHILE OPERATING SWEEPER

DUMPING OF SWEEPER

To dump sweeper hopper bag, simply tip the sweeper forward 
or lift off the complete hopper bag frame.

Always dump hopper after each use. Damp or wet grass 
and leaves will cause damage to hopper if stored for long 
periods of time.

CAUTION: DO NOT DUMP THE SWEEPER 
TOO CLOSE TO A FIRE AS THE BRUSHES 
AND BAG CAN BE DESTROYED BY 
EXCESSIVE HEAT OR FLAME.

STORAGE

The entire unit may be hung on a wall or the hopper bag 
frame can be removed for storage.

LUBRICATION/MAINTENANCE

The bearings in the sweeper have been prelubricated at 
the factory. It is recommended that a few drops of light oil 
be added to the brush shaft bearings twice a year. The 
wheels should be removed to clean gears every two years. 
After cleaning, apply an even coat of light grease. See 
figures 12, 13 and 14.

NOTE:

To remove the wheel, pop off hub cap with a screw 
driver and remove retaining "E" ring and flat washer.

FIGURE 12

OPERATION

Take care when operating your sweeper. Operating your 
sweeper according to these instructions will help prevent 
damage and prolong the life of your sweeper.

BRUSH HEIGHT ADJUSTMENT

To adjust your sweeper brushes to the best operating height, 
loosen the hand knob and slide the height adjustment tube 
down to raise or up to lower the brushes. Best adjustment 
is when brushes are set 1/2" down into the grass. Always 
mow grass to even height before sweeping. See figure 11.

FIGURE 11

Содержание 45-02183













Отзывы: