background image

5

FIGURE 6

13. Assemble the leg stand tube to the long handle tube

using  two  1/4"  x  1-1/2"  hex  bolts.    Secure  tightly
with two 1/4" hex lock nuts.  See figure 5.

14. Place a vinyl cap onto the end of the leg stand tube.

See figure 5.

FIGURE 4

FIGURE 5

15. Assemble the flow control link (end with small hole)

to the flow control arm using a 1/4" x 3/4" hex bolt,
a nylon washer and a 1/4" hex lock nut as shown in
figure  6. 

Tighten carefully. 

The  flow  control  link

should not be loose but should pivot with no more
than slight resistance.

FLOW CONTROL

LINK

FLOW 

CONTROL 

ARM

1/4" HEX

LOCK NUT

1/4" x 3/4"

HEX BOLT

SMALLEST 

HOLE

NYLON

WASHER

IMPORTANT:  Do Not

  assemble  long  handle  tube  on

same side of crossover tube as shaft support plate.
Assemble on opposite side.

9.

Place the long handle tube onto the crossover tube
on the 

opposite

 side from the shaft support plate.

Fasten with 3/8" hex bolt, flat washer and hex lock
nut  removed  in  the  previous  step.    See  figures  3
and 4. 

 Do not tighten at this time.

10. Assemble  two  handle  braces  to  the  inside  of  the

hopper frame, one on each side, using two 1/4" x
1-3/4" hex bolts and two 1/4" lock nuts. See figure
4.  

Do not tighten at this time.

11. Assemble the other end of the two handle braces

to  the  long  handle  tube  using  a  1/4"  x  1-3/4"  hex
bolt  and  1/4"  lock  nut.

 Do not tighten at this

time.

See figure 4.

12.

Tighten

  all  hex  lock  nuts  and  bolts  in  same  se-

quence as assembled in steps 9 through 11.  See
figure 4.

HANDLE TUBE (LONG)

1/4" x 1-1/2"
HEX BOLTS 

1/4" 
LOCK 
NUT

VINYL CAP

LEG STAND TUBE

3/8" HEX 
BOLT

3/8" HEX 
LOCKNUT

FLAT WASHER

HANDLE TUBE (LONG)

HEX BOLT 
1/4" x 1-3/4"

HEX BOLT 
1/4" x 1-3/4"

HITCH 
BRACE

1/4" 
LOCK 
NUT

CROSSOVER
TUBE

SHAFT
SUPPORT
PLATE

Содержание 45-02102













Отзывы: