background image

5

5. SERVICE

a. 

Have your power tool serviced by a qualifi ed repair person using only identical replacement parts. 
This will ensure that the safety of the power tool is maintained.

b.  Only use original Festool parts for repair and maintenance. The use of incompatible accessories or 

spare parts can result in electric shocks or other injuries.

Safety Warnings for Concrete Grinders

Safety Warnings Common for Grinding
• 

This power tool is intended to function as a grinder. Read all safety warnings, instructions, 
illustrations and specifications provided with this power tool. 
Failure to follow all instructions listed 
below may result in electric shock, fire and/or serious injury.

• 

Operations such as sanding, wire brushing, polishing or cutting-off are not recommended to be 
performed with this power tool.
 Operations for which the power tool was not designed may create a 
hazard and cause personal injury.

• 

Do not use accessories which are not specifically designed and recommended by the tool 
manufacturer
. Just because the accessory can be attached to your power tool, it does not assure safe 
operation.

• 

The rated speed of the accessory must be at least equal to the maximum speed marked on the 
power tool.
 Accessories running faster than their rated speed can break and fly apart.

• 

The outside diameter and the thickness of your accessory must be within the capacity rating of 
your power tool.
 Incorrectly sized accessories cannot be adequately guarded or controlled.

• 

Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted 
by flanges, the arbour hole of the accessory must fit the locating diameter of the flange.
 Accessories 
that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively 

Symbols used in this manual

V…….........volts
A…….........amperes
Hz…….......hertz
W……........watt
~………....alternating current

n

 

………...rated speed

min

-1

….......revolutions or reciprocation

  

per minute

.........warning of general danger

 .…..class II tool        

 .......read these instructions

......always wear eye protection

......always wear a dust mask.

 .....always wear hearing protection  

 .....wear safety-approved hard hat

  do not dispose of electric tools,     
  accessories and packaging together
   with household waste material

Содержание G5 125

























Отзывы: