Agilent Technologies U1251A Скачать руководство пользователя страница 61

Страница: 61 / 168

Features and Functions 3

Agilent U1251A/U1252A User’s and Service Guide

Refresh Hold

The hold function allows operators to hold the displayed

digital value. The bar- graph is not held, fix proportional to

real measurement value. You can use the setup mode to

enable the

Refresh Hold

when you are working on a diffi-

cult measuring field. This function will auto trigger or

update Hold value with new measuring value, and sound a

tone to remind user.

Press

button to enter Refresh Hold mode. The present

value will be held, and the sign of

will be lit. It will be

ready to hold new measuring value once the variation of
measuring value exceeds the setting of variation count, and
the sign of

is flashed. The hold value will be updated

until the measuring value is stable, and then it stops
flashing and lit

and sound a tone to remind user.

Press

again to disable this function.

Содержание U1251A









































































































































































Результаты поиска

Содержание U1251A

Отзывы:

Похожие инструкции для U1251A

Бренды по названию

Популярные бренды

Agilent Technologies U1251A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1251A

Отзывы:

Похожие инструкции для U1251A

Бренды по названию

Популярные бренды