manualshive.com logo in svg

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 65 / 202

Поделиться
Скачать
Agilent Technologies n5181a Скачать руководство пользователя страница 65

 

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Troubleshooting 

The Green Front Panel Power Switch LED or Yellow Standby LED is Not Working 

1-57

The Green Front Panel Power Switch LED or Yellow Standby LED is Not Working

The power switch and standby LEDs are controlled by the +5.1 Vdc standby line. The +5.1 Vdc standby line is supplied by the A1 Power 
Supply and is routed through the A3 RF assembly to the front panel. 

With the signal generator plugged in and the power turned off, the yellow standby LED should be on. When the signal generator is turned on, 
the yellow standby LED should turn off and the green front panel power switch LED should turn on. If either of these LEDs are not 
functioning as expected, complete the following procedure to correct the problem.

1.

Remove the outer and inner instrument covers. Refer to 

Chapter 3, "Assembly Replacement"

 for instructions on removing the 

instrument covers.

2.

Using 

Figure 1-24

, check the green DS3 LED on the A3 RF assembly.

•

If DS3 is on, continue to 

step 3

.

•

If DS3 is off, go to 

step 4

.

3.

Using 

Figure 1-24

, press line switch S1 on the A3 RF assembly.

Figure 1-24 Line Switch

a.

Using 

Figure 1-25

, verify that the following power supply voltage LEDs are on. 

•

+3.3VDF, DS1

•

+5VDF, DS2

•

+5.1VSBF, DS3

•

+12VDF, DS4

•

+32VAF, DS5

•

+5VAF, DS6

•

+9VAF, DS7

•

+15VAF, DS8

•

-7VAF, DS9

•

-15VAF, DS10

DS3

S1

Front Panel

Rear Panel

深圳德标仪器 

135-1095-0799

Содержание n5181a











































































































































































































Отзывы:

Нет отзывов