Agilent Technologies n5181a Скачать руководство пользователя страница 195

Страница: 195 / 202

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Post-Repair Procedures and Performance Verification

Leveled Output Power Verification (N5161A/62A

/81A/82A Only)

4-15

N5162A

/82A Output Power Test Procedure

Zero and calibrate the power sensor to the power meter:

Connect the equipment as shown below:

Preset the signal generator: Press

Preset

Select the factory-supplied waveform

SINE_TEST_WFM

Press

Mode > Dual ARB > Select Waveform

Highlight the

SINE_TEST_WFM

waveform.

Press

Select Waveform

Turn the arbitrary waveform player on: Press the

ARB

softkey to highlight

Turn RF on: Press

RF On/Off

so that the RF On/Off LED lights.

Verify modulation is off:

Press

Mod On/Off

so that the Mod On/Off LED turns off.

Set the signal generator frequency to the first value listed in

Table 4-11

Press

Frequency

338

MHz

The N5161A/62A performs the identical internal tests as in the MXG via a LAN connection to a Web Server. The front panel displays all hardkeys, softkeys and test results

as depicted in the illustration. For information on Web-Enabled Control refer to

“Accessing the MXG Web-Enabled Page” on page 1-18

and to the

Programming

Guide.

Table 4-11 Leveled Output Power Relative to

Frequency

(MHz)

Limit

(dB)

338

0.25dB

425

0.25dB

538

0.25dB

675

0.25dB

850

0.25dB

1075

0.25dB

1350

0.25dB

1700

0.25dB

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 195 / 202

Результаты поиска

Содержание n5181a

Отзывы: