manualshive.com logo in svg

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 183 / 202

Поделиться
Скачать
Agilent Technologies n5181a Скачать руководство пользователя страница 183

 

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Post-Repair Procedures and Performance Verification 

Post Repair Procedures 

4-3

Assembly Removal and Installation Procedure

NOTE

This section is meant to be a high level overview of the process for replacing an assembly.

1.

Faulty/bad board assembly is identified by using the troubleshooting information in 

Chapter 1

.

2.

Before removing the bad assembly, use the Remove Assembly service menu to transfer the assembly’s array information, by pressing the 
corresponding softkey:

 Prepare 

<

CPU/RF/BBG

> 

Assembly For Removal

. (Refer to 

Assembly Installation and Removal 

Overview

.)

CAUTION

Do 

not

 proceed with assembly replacement until step 

2

 has been completed. Failure to perform this step can result in the 

hardware not functioning optimally, resulting in instrument errors and possibly self-test failures.

3.

Replace the faulty/bad assembly.

4.

Press the corresponding Install Assembly menu softkey: 

Finalize

 <

CPU/RF/BBG

> 

Assembly Installation

. (Refer to 

Assembly Installation and Removal Overview

.)

CAUTION

Do not proceed with Assembly replacement until step 

4

 has been completed. Failure to perform this step can result in the 

hardware not functioning optimally, resulting in instrument errors and possibly self-test failures.

Service Procedure

CAUTION

After replacing an assembly, it is critical to do a backup or restore in the instrument—as indicated in the tables below—to 
return the instrument to full configuration capability. Refer to 

Table 4-1

 and 

Table 4-2 on page 3

.

After replacing an assembly, check the following tables to see if you should run the service procedure. If your instrument has firmware 
version A.01.04, you must upgrade to A.01.10 or later prior to replacing any assembly. If you do not upgrade to A.01.10 or later your license 
key data will not be available and all license key enabled options will not work.

•

If you did not upgrade your firmware to A.01.10 prior to replacing an assembly refer to 

Table 4-1

.

•

If you did upgrade your firmware to A.01.10 or later, refer to 

Table 4-2

.

Table 4-1 Assembly Replaced with A.01.04 firmware installed – Backup

Condition

Procedure

Upgrading from A.01.04 to A.01.10 or later.

With Error:

“617 Configuration Error: Instrument licenses have 
not been copied to backup storage. Use the service 
procedure to copy license keys to backup storage”

1.

Turn the signal generator off.

2.

Press and hold 

Preset

, turn the signal generator on, continue to hold 

Preset

 

for 10 seconds.

3.

Press: 

Continue

 > 

Next Page

 > 

Backup License Data

 > 

Done

4.

Cycle the power on the signal generator.

Cannot upgrade to A.01.10 or later due to a hardware 
failure.

1.

Replace the A5 CPU. Refer to 

Chapter 3, “Assembly Replacement.”

2.

Upgrade firmware.

All other conditions not mentioned above

Not supported. Upgrade to A.01.10 or later.

Table 4-2 Assembly Replaced with A.01.10 or later firmware installed – Restore/Backup 

Condition

Procedure

Installed new A5 CPU assembly.

With Error:

“617 Configuration Error: The instrument has no 
frequency range option installed. Use the service 
procedure to recover instrument licenses from the 
backup.”

1.

Turn the signal generator off.

2.

Press and hold 

Preset

, turn the signal generator on, continue to hold 

Preset

 

for 10 seconds.

3.

Press: 

Continue

 > 

Next Page

 > 

Restore License Data from Backup

 > 

Done

4.

Cycle the power on the signal generator.

NOTE

If this procedure fails, the signal generator may be limited to 1 GHz 
and all options could be missing. Contact an Agilent Technologies 
service support person for assistance.

深圳德标仪器 

135-1095-0799

Содержание n5181a











































































































































































































Отзывы:

Нет отзывов