Agilent Technologies N4970A Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 30

Agilent Technologies N4970A Скачать руководство пользователя страница 25

Operation

PRBS Generator 10 Gb/s User Guide

25

Connector Description DC Level

DC Level

Z0

Notes

M1 – M3

Mark/space

select

N/A

N/A

N/A

Selected by closure

to lower pin. Refer

to Figure 6.

Reset

Reset PRBS N/A

N/A

N/A

Selected by closure

to lower pin. Refer

to Figure 6.

The turning of the cable or connector while connecting the coupling nut of

the connector turns the center contacts while they are engaging. This wears

the plating, thereby decreasing the signal integrity and operating life of the

connectors. Hold the body of the connector while using a torque wrench to

loosen the coupling nut.

4.5

System Verification

Figure 7 shows a configuration used to verify the performance of the PRBS

source with an external clock. The N4970A internal clock can also be used,

with the CLK/16 output triggering a sampling oscilloscope.

This verification confirms the operation of five pattern lengths, mark density,

and waveshape characteristics.

«
...
23
24
25
26
27
...
»

Содержание N4970A































Отзывы:

Нет отзывов