manualshive.com logo in svg

Agilent Technologies Infinium DCA 86100A, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies Infinium DCA 86100A Скачать руководство пользователя страница 104

5-8

Instrument Refurbishment

Refurbishing an 86100C (Alternate Method)

Refurbishing an 86100C (Alternate Method)

N O T E

The process to clear the hard drive for instrument re-sale is very time consuming; therefore, 
performing the procedure 

“Refurbishing an 86100C” on page 5-5

, is the recommended method 

which involves replacing the hard drive with a new one.

On the 86100C all software option license files, such as Option 100, Option 200, and Option 201 
must be removed from the hard drive. A new backup disk image is created, based on the latest 
data from the Factory. 

The latest firmware will be installed. All recommended preventative maintenance will be per-
formed. Modifications and service notes should be installed as required. Follow all the adjust-
ment steps in 

Chapter 3

 before performance testing. Complete a full performance verification 

from 

Chapter 4

.

The hard drive recovery procedure restores the instrument’s hard disk to Factory condition.

Procedure

Complete all the steps to refurbish the 86100C in the order presented below. This ensures that the 
recovery image stored on the hard drive is the same as a new instrument from the factory.

1 Factory Recondition the 86100C Hard Disk Drive. On 86100C instruments, the hard disk drive 

has four partitions: 

• Infiniium drive C contains the operating system, the 86100C application, timebase calibration 

file, serial number, and software license files.

• The User Drive D contains customer data files. It also contains automatically backed up dupli-

cates of the timebase calibration file, serial number, and software license files.

• A hidden un-named partition contains the recovery image.

• Another hidden un-named partition contains a bootable DOS file.

Drive C Recovery

2 Connect a keyboard to the instrument.

3 Turn on the instrument. After approximately 30 seconds, look for the following displayed text. 

Immediately, press the down arrow key on the keyboard to select Emergency Backup And 
Recovery. Then, press the Enter key.

4 After more text is displayed, press the Enter key to display the following screen:

Содержание Infinium DCA 86100A













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды