Agilent Technologies Infinium DCA 86100A Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 268

background image

5-5

Instrument Refurbishment

Refurbishing an 86100C

Refurbishing an 86100C

The hard drive is replaced with a new one. A new Certificate of Authenticity sticker is installed
on the rear panel of the DCA mainframe. All recommended preventative maintenance will be
performed. Modifications and service notes should be installed as required. Follow all the adjust-
ment steps in

before performance testing. Complete a full performance verification

from

Complete all the steps to refurbish the 86100C in the order presented below. This will ensure that
the DCA will perform as close to new as possible.

Procedure

1 Install a new hard drive.

Refer to “To Replace the A9 Hard Drive” on page 7-39

for help with

replacing the hard drive.

2 Install a new COA.

Refer to “Rear View Identification” on page 10-14

to obtain the part number

of the Certificate of Authenticity (COA) label. Refurbishing DCAs with Microsoft Windows XP
operating system requires that a new COA label be purchased and installed on the rear panel of
the DCA mainframe. Remove the old label before installing the new one.

3 Install a new serial number tag. Recreate the serial number tag to reflect the shipping options e.g.

remove 86100C options 001, 100 replace with 86100C option 001.

4 Perform preventative maintenance.

Refer to “Preventative Maintenance, 86100A/B/C” on page

.

5 Complete All Adjustments.

Refer to “Adjustments” on page 3-1

.

6 Complete Performance Verification.

Refer to “Performance Verification” on page 4-1

.

Re-seal the OS

Re-sealing the OS prepares the operating system for the customer first run experience. This
allows the new owner of the DCA to properly license Windows XP the next time the DCA is
turned on.

7 In the DCA click Exit on the File menu to close the 86100C application.

8 When asked “are you sure you want to exit 86100C”, click Yes.

9 Click “Start” and select “Run...”.

10 Type the following in the Run window:

c:\windows\i386\$OEM$\reseal.bat

11 Click OK.

12 Open (Run) the batch file.

13 At the completion of the batch file run, the DCA will shut down.

Create New Backup Image of Drive C

Creates a backup copy of the C partition with all the recently created files, and stores it on a hid-
den partition.

«
...
99
100
101
102
103
...
»

Содержание Infinium DCA 86100A













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Infinium DCA 86100A

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: Backyard Discovery Страницы: 79

Бренд: Badger Meter Страницы: 16

Бренд: Cadman Страницы: 84

Бренд: EAW Страницы: 2

Бренд: abc Страницы: 28

Бренд: Gardigo Страницы: 24

Бренд: Gardner Bender Страницы: 8

Бренд: Garantia Страницы: 4

Бренд: NARIKA Страницы: 2

Бренд: Panta Safe Light Страницы: 2

Бренд: Calrec Страницы: 70

Бренд: Kärcher Страницы: 88

Бренд: Pari Страницы: 12

Бренд: laerdal Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды