10- 7
Channel Commands
PROBe
PROBe
Command
:CHANnel<N>:PROBe <attenuation_factor>[,{RATio |
DECibel}]
The :CHANnel<N>:PROBe command sets the probe attenuation factor and,
optionally, the units for the probe attenuation factor. The range of the probe
attenuation factor is from 0.0001 to 1,000 and from
−
80 dB to 60 dB.
The reference factors that are used for scaling the display are changed with this
command, and affect automatic measurements and trigger levels.
The “,DEC” or “,RAT” also sets the “mode” for the probe attenuation. This mode
also determines the units that may be used for a subsequent command. For
example, if you select RATio mode, then the attenuation factor must be given
in . In “DECibel” mode, you can specify the units for the argument as “dB”.
<N>
An integer, 1-2, for two channel Infiniium Oscilloscope.
An integer, 1-4, for all other Infiniium Oscilloscope models.
<attenuation
_factor>
A real number from 0.0001 to 1,000 for the RATio attenuation units or from
−
80 dB to 60 dB for the DECibel attenuation units.
Example
This example sets the probe attenuation factor for a 10:1 probe on channel 1 in
ratio mode.
10 OUTPUT 707;":CHANNEL1:PROBE 10,RAT"
20 END
Содержание Infiniium 8000A
