Agilent Technologies G4782A Скачать руководство пользователя страница 80

Страница: 80 / 202

1260 SFC Binary Pump

Error Information

Module Error Messages

Missing Pressure Reading

Error ID: 2054

The pressure readings read by the pump ADC (analog-digital converter) are
missing.

The ADC reads the pressure signal of from the damper every 1ms. If the
readings are missing for longer than 10 s, the error message is generated.

Wrong Pump Configuration

Error ID: 2060

At switch-on, the pump has recognized a new pump configuration.

The binary pump is assigned its configuration at the factory. If the active inlet
valve and pump encoder of channel B are disconnected, and the binary pump
is rebooted, the error message is generated.

Probable cause

Suggested actions

Damper disconnected.

Please contact your Agilent service
representative.

Defective damper.

Please contact your Agilent service
representative.

Defective main board.

Please contact your Agilent service
representative.

Probable cause

Suggested actions

Active-inlet valve and pump encoder of
channel B disconnected.

Please contact your Agilent service
representative.

Содержание G4782A











































































































































































































Результаты поиска

Содержание G4782A

Отзывы:

Похожие инструкции для G4782A

Бренды по названию

Популярные бренды

Agilent Technologies G4782A, Руководство пользователя

Результаты поиска

Содержание G4782A

Отзывы:

Похожие инструкции для G4782A

Бренды по названию

Популярные бренды