manualshive.com logo in svg

Agilent Technologies G3183B, Инструкция по установке и эксплуатации

Поделиться
Скачать
Agilent Technologies G3183B Скачать руководство пользователя страница 24

24

Installation and Operation Guide

2

Installation

Connect the Makeup Gas Supply

Connect the makeup gas source to the Pneumatic Control Module or Auxiliary 
Pressure controller.

To supply the makeup gas from a Pneumatic Control Module (PCM)

1

Connect the tubing from the PCM to the length of stainless steel tubing from 
the kit with a union.

2

Connect the free end of the stainless steel tubing to the tubing from the 
splitter assembly with a union. See 

Figure 10

.

To supply the makeup gas from an Auxiliary Pressure controller

1

Install the brown-dot frit (part no. 19231-60610) in the output channel. See 
your GC manual for details.

2

Connect the tubing from the Auxiliary Pressure controller to the tubing 
from the splitter assembly with the 1/8 to 1/16-inch stainless steel reducing 
union.

This completes the hardware installation.

Figure 10

Plumbing a PCM makeup supply

PCM

Union

Union

To splitter

Stainless

steel

tubing

Содержание G3183B

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды