background image

TECHNICAL INFORMATION 

 1

9/24

87-900-053-01 (

F

)

 

CONTROLLER SPECIFICATIONS 

 

Operation 

All type and size of  
VacIon pump 

Input: 

-  Voltage 
-  Power 
-  Fuse 

 

24 Vdc ±4 Vdc 
60 W 
2 x T 3.15 A 

Output: 

-  Voltage 
 
 
 
-  Current 
 
 
-  Power 

 

±5000 Vdc ±10% (refer  to 
the following figure) (polarity 
through internal card)  
 
15 mA (short circuit) (refer to 
the following figure)  
 
21 W 

Dual Current 
Recorder 
Output: 
-  Rec Out1 
 
 
 
 
 
 
 
 
-  Rec Out2 

 
 
 
0 to 10 Vdc (10 V correspond 
to 10 mA); 
resolution of 10 mV minimum 
(corresponding to 10 µA)  
Available on front panel BNC 
connector and at pins 1 and 6 
of rear panel Accessory 
connector. 
 
0 to 10 Vdc (10 V correspond 
to 1 mA); 
resolution of 10 mV 
minimum (corresponding  
to 1 µA) 
Available at pins 2 and 6 of 
rear panel Accessory 
connector. 

 

 

 

Voltage  
Recorder  
Output: 
-  Rec Out 

 
 
 
0 to 5 V (corresponding to  
0 to 5 kV with 1 V 
corresponding to 1 kV in 
linear mode) 
Available at pins 4 and 8 of 
rear panel Accessory 
connector. 

Operating  
temperature 

0 °C to 45 °C 

Storage  
temperature 

-20 °C to +70 °C 

Radio interference 
suppression 

EN 55011 class A Group 1 
EN 61000-4-2 
EN 61000-4-4 
EN 61000-4-3 

Safety EN 

61010-1 

Installation category  II 

Pollution degree 

Output connector: 
-  High voltage 
 
 
 
 
-  Accessory 

FISCHER type:  
part number 105 A049  
for model 929-0196 
KINGS type:  
part number 1064-1  
for model 929-0197 
J 001 input/output  
signal (9-pin "D" type socket) 

Weight 

1.3 Kg       2.86 lbs 

 
 

Содержание 929-0196

































Отзывы: