manualshive.com logo in svg

Agilent Technologies 85103E, Руководство по установке

Поделиться
Скачать
Agilent Technologies 85103E Скачать руководство пользователя страница 12

2

85103E Performance Upgrade Installation Manual

85103E Upgrade Package (8510A to 8510C)

Installing the Upgrade

Installing the Upgrade

Use this package to upgrade an 8510A (with serial number below 03000) to an 8510C. With 
this package, you will do the following:

• Check the 8510A operation.

• Transfer data from tape to disk.

• Install a BNC connector.

• Replace three printed circuit board assemblies.

• Reroute cables.

• Attach new labels.

• If required, upgrade the 8360.

• Reconnect the system.

• Load the 8510C operating system.

• Check the 8510C operation.

• Load and check the calibration kit definitions.

NOTE

Agilent Technologies does not recommend customer installation of this 
upgrade. The Agilent 85103E performance upgrade package comes with 
prepaid installation. Refer to 

“Contacting Agilent” on page iv

 to arrange 

for a service engineer to install the upgrade package.

Warranty Information

Installation of an upgrade does not affect the existing instrument warranty in any way. 
Specifically, it does not extend the current instrument warranty. Any parts supplied in an 
upgrade package carry a 90-day replacement-part warranty.

Source Compatibility

For complete compatibility with revision C.07.00 or greater firmware, your source must be 
an Agilent 8360 series source. If an 8360 series source is not used, power domain and 
receiver calibration functions will not work.

The 8510C works with all 8360 synthesized sweeper models. However, some 8360 
instruments must be upgraded to take advantage of two 8510C system features (quick step 
mode and test port power flatness correction). Refer to 

“Upgrading an 8360 Source.”

NOTE

Agilent 8340, 8341, and 8350 series sources are out of support life and 
are no longer recommended for use in 8510C systems.

Please consult with your Agilent customer engineer for more information on upgrading a 
network analyzer and source firmware.

Содержание 85103E










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды