Agilent Technologies 5977B Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 258

Agilent Technologies 5977B Series Скачать руководство пользователя страница 23

Introduction

1

5977B Series MSD Troubleshooting and Maintenance Manual

23

Dangers unique to GC/MSD operation

Hydrogen presents a number of dangers. Some are general, others are unique
to GC or GC/MSD operation. Dangers include, but are not limited to:

•

Combustion of leaking hydrogen

•

Combustion due to rapid expansion of hydrogen from a high-pressure
cylinder

•

Accumulation of hydrogen in the GC oven and subsequent combustion (see
your GC documentation and the label on the top edge of the GC oven door)

•

Accumulation of hydrogen in the MSD and subsequent combustion

Hydrogen accumulation in an MSD

All users should be aware of the mechanisms by which hydrogen can
accumulate (

) and know what precautions to take if they know or

suspect that hydrogen has accumulated. Note that these mechanisms apply to

all

mass spectrometers, including the MSD.

WA R N I N G

The MSD cannot detect leaks in inlet or detector gas streams. For this reason, it is
vital that column fittings should always be either connected to a column

,

or have a

cap or plug installed.

Table 4

Hydrogen accumulation mechanisms

Mechanism

Results

Mass spectrometer turned off

A mass spectrometer can be shut down
deliberately. It can also be shut down accidentally
by an internal or external failure. There is a safety
feature that will shutdown the flow of carrier gas in
the event of an MSD foreline pump shutdown.
However, if this feature fails, hydrogen may slowly
accumulate in the mass spectrometer.

«
...
21
22
23
24
25
...
»

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды