Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 233

Страница: 233 / 254

CI Maintenance



To Switch from an EI XTR, SS, or Inert Source to the CI Source

5977B Series MSD Operating Manual

233

To Switch from an EI XTR, SS, or Inert Source
to the CI Source

Procedure

Vent the MSD. (See

“To Vent the MSD”

on page 136.)

Open the analyzer. (See

“To Open the Analyzer Chamber”

on page 176.)

Remove the EI source. (See

“To Remove the EI XTR, SS, or Inert Source”

page 196.)

If removing an XTR source, remove the brown extractor wire from the
ceramic source board and store it with the EI XTR source. (See

Figure 55

page 179.)

Install the CI source. (See

“To Install the CI Source”

on page 250.)

Install the CI/Extractor interface tip seal if it is not already installed
(p/n G3870-20542). (See

“To Install the GC/MSD Interface Tip Seal”

page 50.)

Close the analyzer. (See

“To Close the Analyzer Chamber”

on page 220.)

Pumpdown the MSD. (See

“To Pumpdown the MSD in CI Mode”

page 148.)

CAUTION

Always verify MSD performance in EI before switching to CI operation.

Always set up the CI MSD in PCI first, even if you are going to run NCI.

CAUTION

Electrostatic discharges to analyzer components are conducted to the side
board where they can damage sensitive components. Wear a grounded
antistatic wrist strap. (See

“Electrostatic discharge”

on page 171.) Take

antistatic precautions

before

you open the analyzer chamber.

Содержание 5977B CI MSD































































































































































































































































Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации

Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды