Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 223

Страница: 223 / 254

CI Maintenance



To Switch from the EI HES to the CI Source

5977B Series MSD Operating Manual

223

To Switch from the EI HES to the CI Source

Procedure

Vent the MSD. (See

“To Vent the MSD”

on page 136.) The software will

prompt you for the appropriate actions.

Open the left side access panel. (See

“To Open the MSD Covers”

page 135.)

Open the analyzer chamber. (See

“To Open the Analyzer Chamber”

page 176.)

Remove the EI HES. (See

“To Remove the EI HES”

on page 178.)

Make sure the EI HES source has cooled and then place it in its storage

container.

Remove the EI HES radiator. (See

“To Remove the EI HES Radiator”

page 224.)

Place the EI HES radiator in the storage container.

Remove the CI source radiator from the storage container.

Install the CI source radiator. (See

“To Install the CI Source Radiator”

page 227.)

Remove the CI source from the storage container.

Install the CI source. This requires shortening the column so that it protrudes

from the transfer line by 1 to 2 mm. (See

“To Install the CI Source”

page 250.)

Pumpdown the MSD. (See

“To Pumpdown the MSD in CI Mode”

page 148.)

CAUTION

Always verify GC/MSD performance in EI before switching to CI operation.

CAUTION

Electrostatic discharges to analyzer components are conducted to the side
board where they can damage sensitive components. Wear a grounded
antistatic wrist strap. (See

“Electrostatic discharge is a threat to MSD

electronics”

on page 22.) Take antistatic precautions

before

you open the

analyzer chamber.

Содержание 5977B CI MSD































































































































































































































































Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации

Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды