Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 209

Страница: 209 / 254

General Maintenance



To Assemble an EI SS or Inert Source

5977B Series MSD Operating Manual

209

To Assemble an EI SS or Inert Source

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Hex ball driver, 1.5 mm (8710-1570)

•

Hex ball driver, 2.0 mm (8710-1804)

•

Wrench, open-end, 10 mm (8710-2353)

Procedure

Refer to the exploded parts view

Figure 67

and EI SS and EI Inert parts list

Table 22

on page 210 while using this procedure.

Assemble the repeller assembly.

Install the repeller block insert into the source heater block assembly.

Install the repeller insulators into the source heater block assembly and
repeller block insert.

Install the repeller through the repeller insulators, then put the flat
washer followed by the belleville spring washer onto the end of the
repeller shaft, and secure finger tight with the repeller nut.

Insert the drawout plate and the drawout cylinder into the source body.

Assemble the ion focus lens, entrance lens, and lens insulators.

Slide these assembled parts into the source body.

Install the setscrew that holds the lenses in place.

Install the interface socket.

Attach the repeller assembly to the source body using the two gold plated
screws and spring washers.

Install the filaments using the two gold plated screws and spring washers.



CAUTION

Do not overtighten the repeller nut or the ceramic repeller insulators will break
when the source heats up. The nut should only be finger-tight.



Содержание 5977B CI MSD































































































































































































































































Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации

Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды