Agilent Technologies 53210A Скачать руководство пользователя | Manualshive

Страница: 16 / 44

background image

16

53210A/53220A/53230A

Option

Installation

53210A/53220A/53230A Option Installation

53210A/53220A/53230A Rear Panel Parallel Inputs (Option 201)

Installation of Option 201 (Rear Panel Parallel Inputs) must be performed

by technicians at an Agilent Technologies Service Center.

The purchase of

this option (53200U- 201) includes the cost of Agilent installing the

option and verifying that the instrument is operating correctly

. You

must send your instrument and the option kit to Agilent for installation to

occur.

Obtaining Installation Service (worldwide)

To arrange for option installation, contact Agilent Technologies at one of

the following telephone numbers:

•

United States:(800) 829- 4444

•

Europe: 31 20 547 2111

•

Japan: 0120- 421- 345

For other locations, go to

www.agilent.com/find/assist

or contact your Agi-

lent Technologies Representative. The Service Center will provide informa-

tion on how to ship the instrument and the option kit to the center for

installation.

Repackaging for Shipment

In preparation for shipment to Agilent, be sure to:

1. Attach a tag to the instrument identifying the owner and indicating the

required installation (Option 201). Include the model number and full

serial number on the tag.

2. Retain all loose accessories, power cords, CDs, manuals, and the like.

Only ship the instrument and the option kit.

3. Place the instrument and the option kit in the instrument's original

«
...
14
15
16
17
18
...
»

Содержание 53210A













































Отзывы:

Нет отзывов

Похожие инструкции для 53210A

Бренд: CET Страницы: 8

Бренд: Record Страницы: 28

Бренд: RCH Страницы: 62

Бренд: Fiessler Страницы: 161

Бренд: Uniwell Страницы: 130

Бренд: ECR Страницы: 30

Бренд: Nautilus Hyosung Страницы: 28

Бренд: Sam4s Страницы: 5

Бренд: ratiotec Страницы: 20

Бренд: Sam4s Страницы: 7

Бренд: TEC Страницы: 6

Lidar People Counter

Бренд: daviteq Страницы: 93

Бренд: TEC Страницы: 52

Бренд: BEKA Страницы: 32

Бренд: Omron Страницы: 2

Бренд: Omron Страницы: 28

GV-3D People Counter V2

Бренд: GeoVision Страницы: 16

PRO 86 MIX EURO

Бренд: Pro-Line Boats Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды