Agilent Technologies 34945A Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 124

background image

Hardware Configuration

2

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

27

Agilent 87104/87106/87406 - L7104/L7106/L7204/L7206 Coaxial Switches

Figure 2-4 shows the pin definitions and orientation for the Y1151A
distribution board, the Agilent 87104, 87106, and 87406 series switches, and
the L7104, L7106, L7204, and L7206 L series switches.

Figure 2-4. Agilent 871x / 874x / L71x / L72x Pin Definition and Orientation.

13

11

9

7

5

3

1

15

14

12

10

8

6

4

2

16

Pin

Definition

Pin

Definition

1

+VR

2

Indicator Common

3

Drive Path 1

4

Indicator 1

5

Drive Path 2

6

Indicator 2

7

Drive Path 3

8

Indicator 3

9

Drive Path 4

10

Indicator 4

11

Drive Path 5

12

Indicator 5

13

Drive Path 6

14

Indicator 6

15

GND

16

Open All Paths

Agilent 87104 / 87106 / 87406

Agilent L7104/L7106/L7204/L7206

DC Connector Pin Out

Y1151A

Distribution Board Connector

(87104 / 87106 / 87406)

(L7104 / L7106 / L7204 / L7206)

Y1159A Cable

87406

87104 / 87106

L7104 / L7106 / L7204 / L7206

* Paths 1 and 4 of the 87104, L7104,
and L7204 are not connected

LED1 Connector

LED2 Connector

Pin

Definition

Pin

Definition

Pin

Definition

Pin

Definition

1

+VI

2

SW1 - Path 1

1

+VI

2

SW2 - Path 1

3

+VI

4

SW1 -Path 2

3

+VI

4

SW2 - Path 2

5

+VI

6

SW1 - Path 3

5

+VI

6

SW2 - Path 3

7

+VI

8

SW1 - Path 4

7

+VI

8

SW2 - Path 4

9

+VI

10

SW1 - Path 5

9

+VI

10

SW2 - Path 5

11

+VI

12

SW1 - Path 6

11

+VI

12

SW2 - Path6

13

+VI

14

Not Used

13

+VI

14

Not Used

15

+VI

16

Not Used

15

+VI

16

Not Used

Y1151A Distribution Board

LED Connector Pins

1

2

15

16

1

2

15

16

N O T E

The pin information for the Agilent switches shown in Figure 2-4 was taken from
the reference documents listed in Table 1-2. Refer to Table 1-2 for information on
accessing these documents from the Agilent web-site.

«
...
33
34
35
36
37
...
»

Содержание 34945A





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 34945A

Бренд: Ubisys Страницы: 40

Бренд: D-Link Страницы: 242

S5170-EI Series

Бренд: H3C Страницы: 46

Бренд: Waters Network Systems Страницы: 16

Бренд: Campbell Страницы: 10

AVS-OCT-6448-210

Бренд: AMX Страницы: 1

Digital Energy STS-400-25-3

Бренд: GE Страницы: 49

Бренд: KanexPro Страницы: 35

Бренд: C&C TECHNIC Страницы: 2

Бренд: KinAn Страницы: 5

Бренд: Harman Страницы: 50

Бренд: Tabs Страницы: 4

EXT-HDMI-CAT5-844

Бренд: Gefen Страницы: 28

IDS-105FE Series

Бренд: Perle Страницы: 2

Total Access 1210

Бренд: ADTRAN Страницы: 4

BOEING 737 STYLE

Бренд: Precision Flight Controls Страницы: 8

Duramax LBZ DSP5

Бренд: EFILive Страницы: 21

Бренд: Shinybow USA Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды