Agilent Technologies 34945A Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 124

background image

Hardware Configuration

2

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

21

Channel Numbering

The 34945EXT uses the following channel numbering scheme:

<

slot #

><

34945EXT #

><

channel

>

where:

slot # -

is the 34980A slot where the 34945A is installed. This is a single digit

between 1 and 8.

34945EXT

#

- is the 34945EXT module. This is a single digit between 1 (the

master 34945EXT) and 8. 34945EXT modules are numbered according to
their position in the daisy-chain sequence relative to the master.

channel

is the channel number in the specified EXT module bank.

Channel numbers are specified using two digits. Examples of the channel
numbers for two 34945EXT modules (the master and one slave) are shown
below below.

An example of this syntax is for a 34945A module installed in

slot 2

of the

34980A is:

ROUT:CLOS (@2141)

which closes

channel 41

(bank 3) on

34945EXT module number 1

.

A range of channels for a 34945A installed in

slot 1

of the 34980A can be

specified as:

ROUT:CLOS (@1101:1278)

which in this example closes all channels on the master 34945EXT (

module

number 1

) and all channels on the slave 34945EXT (

module number 2

).

Channel ranges can extend across banks and across 34945EXT modules.

Module- and Bank-Level Commands

Selected commands within the 34945A SCPI command set contain parameters
that specify the 34945EXT itself, or a bank on the 34945EXT rather than a
channel list. These commands include:

34945EXT #1 (master)

34945EXT #2 (slave)

Bank

Channels

Channels

Bank

Channels

Channels

Bank 1

x101 to x108

x111 to x118

Bank 1

x201 to x208 x211 to x218

Bank 2

x121 to x128

x131 to x138

Bank 2

x221 to x228 x231 to x238

Bank 3

x141 to x148

x151 to x158

Bank 3

x241 to x248 x251 to x258

Bank 4

x161 to x168

x171 to x178

Bank 4

x261 to x268 x271 to x278

«
...
27
28
29
30
31
...
»

Содержание 34945A





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 34945A

Бренд: Eaton Страницы: 8

Бренд: Danfoss Страницы: 6

VNLW-P-1001-MV-N-V

Бренд: Greengate Страницы: 2

HD Flash 4 KD-SW4x1

Бренд: Key Digital Страницы: 12

LS-5500-28C-PWR-SI-OVS

Бренд: H3C Страницы: 86

Бренд: Velleman Страницы: 5

Бренд: Eaton Страницы: 120

SmartSTACK 100 ELS100-16TX

Бренд: Cabletron Systems Страницы: 16

Бренд: Jerguson Страницы: 4

Бренд: Wyrestorm Страницы: 4

Бренд: X-keys Страницы: 4

Бренд: senva Страницы: 2

Бренд: UNIARCH Страницы: 6

Бренд: Zektor Страницы: 30

Бренд: I-Rocks Страницы: 18

Бренд: ATEN Страницы: 9

Бренд: Lantech Страницы: 27

Бренд: Kramer Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды