AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя

Страница: 59 / 74

BU-0101704 R3

Figure 54.

Adjusting Sweep Backboard Height near Center Sump

3. Rotate the backboard so that its lower scraper is resting on 1/4” wood blocks which are placed underneath

the backboard scraper every 3’ (0.9 m). This sets the required clearance between the backboard scraper and
the bin floor.

4. Retighten all the bolts which were loosened.

6.16. Install the Sweep Stop

1. Using the sweep stop as a template, mark and drill the four holes in the bin wall (1). The sweep stop should

be positioned:

•

Far enough from the bin door so that it won’t contact when opened.

•

High enough that the sweep end wheel fender will clear the sweep stop in its raised position. The
bottom slot should be approximately 12"-14" (305mm — 356mm) from the top of the bin floor.

2. Mount the sweep stop (3) to the inside of the bin using four 1/4" x 1" bolts (4), flat washers (6), sealing

washers (5) and nylon locknuts (7).

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

6. ASSEMBLY

Содержание Westeel EasyFlow2 100 Series











































































Результаты поиска

Содержание Westeel EasyFlow2 100 Series

Отзывы:

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренды по названию

Популярные бренды

AGI Westeel EasyFlow2 100 Series, Сборка и инструкция по установке

Результаты поиска

Содержание Westeel EasyFlow2 100 Series

Отзывы:

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренды по названию

Популярные бренды