AGI UTX Series Скачать руководство пользователя страница 9

Страница: 9 / 92

31084 R3

2.6.2 Hydraulic Power Safety

Power Source

• Refer to the rules and regulations applicable to the power

source operating your hydraulic drive.

• Do not connect or disconnect hydraulic lines while system is

under pressure.

• Keep all hydraulic lines away from moving parts and pinch

points.

• Escaping hydraulic fluid under pressure will cause serious

injury if it penetrates the skin surface (serious infection or
toxic reaction can develop). See a doctor immediately if
injured.

• Use metal or wood as a backstop when searching for

hydraulic leaks and wear proper hand and eye protection.

• Check all hydraulic components are tight and in good

condition. Replace any worn, cut, abraded, flattened, or
crimped hoses.

• Clean the connections before connecting to equipment.

• Do not attempt any makeshift repairs to the hydraulic fittings

or hoses with tape, clamps, or adhesive. The hydraulic
system operates under extremely high pressure; such repairs
will fail suddenly and create a hazardous and unsafe
condition.

Lockout

• Always place all hydraulic controls in neutral and relieve

system pressure before disconnecting or working on
hydraulic system.

UTX SERIES – PORTABLE U-TROUGH GRAIN AUGER

2. SAFETY

Содержание UTX Series





























































































Результаты поиска

Содержание UTX Series

Отзывы:

Бренды по названию

Популярные бренды

AGI UTX Series, Инструкция по сборке

Результаты поиска

Содержание UTX Series

Отзывы:

Бренды по названию

Популярные бренды