AGI Grainmaxx GMX16 Скачать руководство пользователя страница 58

Страница: 58 / 92

30869 R8

4.18. Connect the Auger Tube to the Frame

1. Raise the discharge end of auger (e.g. with a front end loader and a strong sling, or with a chain or block and

tackle). The height should be sufficient to clear the undercarriage assembly.

Do not remove tube support until the assembly in this section has been completed.

2. Place the undercarriage beneath the tube assembly.

3. Connect the lower lift arms to the auger tube:

a. Lift and support the lower attach arms on either side of the auger tube back-end brackets.

b. Position stabilizer brackets between the back-arm brackets and corresponding lower reach arms, and

secure the lower reach arms and stabilizer brackets to the back-arm brackets with a tube frame pin, a
lower arm attach bushing, a 7/16” x 3” GR5 bolt, and a 7/16” locknut on each side.

c. Tighten securely.

4. Fasten stabilizer braces to first set of holes (closest to the intake) through the stabilizer brackets with one 5/

8” x 2” bolt and locknut. Place one 5/8” x 2-1/4” bolt and locknut in the remaining set of holes through the
stabilizer braces.

5. Fasten the upper lift arms to the axle: use an axle frame pin, a 1/2” x 1-1/2” GR8 bolt and a 1/2” locknut on

each side. Tighten securely.

6. Attach the tubing cross braces between the upper lift arms by loosely attaching the tubing cross braces

using three 1/2” x 1-1/2” GR8 bolts, two 1/2” x 1-3/4” bolts, five 1/2” flat washers, and locknuts.

7. Attach the lift assist bracket to the track shoe as follows:

a. Align the lift assist with the track shoe, and insert the track shoe pin through the lift assist and the track

shoe. (See

Figure 27

for the correct insertion side).

b. Add the track shoe bushing and then secure the bushing with a 7/16” x 3-1/2” bolt and locknut. Tighten

securely.

8. Attach upper lift arms to the lift assist bracket as follows:

a. Raise and position the top of the upper lift arms on the pin weldments on either side of the lift assist.

b. Secure the upper lift arms on the pin weldments using a upper lift arm bushing, a washer, a 7/16” x 3-1/

2” bolt, and a 7/16” locknuts on each pin weldment.

c. Tighten securely.

9. Lower upper end of auger slowly until track shoe rests against upper track stop and the lift assist stops rest

against track.

10. For 105'/125', attach a short cross-member between the upper lift arms using eight 1/2” x 1-1/2” bolts and

1/2” locknuts. Tighten securely.

4. ASSEMBLY

SWING-AWAY GRAIN AUGER – PORTABLE GRAIN AUGER

Содержание Grainmaxx GMX16





























































































Результаты поиска

Содержание Grainmaxx GMX16

Отзывы:

Бренды по названию

Популярные бренды

AGI Grainmaxx GMX16, Инструкция по сборке

Результаты поиска

Содержание Grainmaxx GMX16

Отзывы:

Бренды по названию

Популярные бренды