AGI 15100SA Скачать руководство пользователя страница 20

Страница: 20 / 82

P1512161 R0

3.4. Before You Begin

Before you assemble the conveyor:

• Familiarize yourself with all the sub-assemblies, components, and hardware that make up the equipment.

• Have all parts and components on hand, and arrange them for easy access.

• Separate the hardware (bolts, nuts, etc.) and lay them out into groups for easier identification during

assembly.

• Ensure there is adequate space to remove the assembled conveyor from the assembly area.

3.5. Hydraulic Fittings and Bolt Tightening

Remember the following basic considerations when tightening hydraulic fittings and bolts:

• Tighten all fasteners to the torque specified in

Section 5.1 – Bolt Torque on page 78

. Do not replace or

substitute bolts, nuts, or other hardware that is of lesser quality than the hardware supplied by the
manufacturer.

All hydraulic fittings should be torqued to the recommended specifications. See

Section 5.2 – Fittings Torque

Values on page 79

Do not over-tighten fittings! Over-tightening hose fittings can crack the fittings or motor body
and will void the warranty.

3.6. Connect the Conveyor Tube to the Hopper

1. Align the conveyor tube and hopper.

2. Fasten the tube flanges together with 7/16" x 1" bolts (2) and 7/16" locknuts (1) (see

Figure 4

). Ensure the

bolts are straight.

Note

A punch can be used to assist alignment. If you are not careful, it is possible to bolt the flanges
together non-concentrically with the bolts crooked through the holes.

Table 3.

Tube Connection Components

Item

Description

7/16" Locknut

7/16" x 1" Bolt GR8

3. ASSEMBLY

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

Содержание 15100SA



















































































Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды

AGI 15100SA, Инструкция по сборке

Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды