manualshive.com logo in svg

AGFA DRYSTAR AXYS, Руководство по обслуживанию

Поделиться
Скачать
AGFA DRYSTAR AXYS Скачать руководство пользователя страница 165

 
 
DD+DIS033.07E 

Repair and Service

Tools and Auxiliary Means

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

 

4.3 

Emergency SW Installation on a printer in "Error - System Failure" state 

 

Purpose 

This chapter describes the SW Installation on a printer in ERROR - SYSTEM 
FAILURE state. 

 

 

IMPORTANT: 

The software installation procedure 
described here formats the hard disk. 

In case you select "NO" at question 
"Do you want to preserve config" the 
configuration data are erased. 

In this case the printer is only in the 
same state than before, if an up-to-
date backup is available.  

In case the CF card is lost or not 
readable the complete printer setup 
has to be redone. 

Emergency SW FOUND
ON EXTERNAL CF-card
Install emergency
SW?  YES (V)  NO (X)

Emergency SW Install
Do you want
to preserve config?
YES (V)  NO (X)

536632gc.cdr

 

 

 

Figure 59 

 

SW 

Installation 

on empty HD 

Edition 1, Revision 0 

DRYSTAR AXYS 

Chapter 3.2 / 59 

10-2007 Type 

5367/100 

Agfa Company Confidential

 

5366_Reg01_017_e.cdr

초

2

 

 

(1)  Insert the CF card with the printer 

"Emergency_Install" software in 
the CF card reader  

(2)  Reboot the printer 

(3)  At question "Do you want to 

preserve config?" select  
"NO" in case you want to erase 
the complete configuration 
"YES" in case want to keep the 
current configuration. Refer to 
Figure 59 and to info below. 

(4)  Follow the further instructions on 

the local keypad. 

(5)  Select menu "5 Restore 

Configuration" to reload the 
previous configuration when 
finished. 

Figure 60 

 

 

 

Содержание DRYSTAR AXYS














































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды