background image

Position: 

Under engine cover, next to coolant

expansion tank
743.500.410.080

DANGER:
Scalding caused by hot coolant vapor
After the vehicle has been operated,
the cooling circuit contains
pressurized, hot coolant. When the
coolant reservoir or circuit is opened,
the coolant escapes in the form of hot
vapor and can cause scalding if
allowed to come into direct contact
with the skin.
Before opening the coolant reservoir
or circuit, switch off the engine and
allow sufficient time for the coolant to
cool down.
The maintenance manual contains all
important information.

Position: 

Right-hand side of tractor, at exhaust as

well as left and right of radiator
743.500.410.060

DANGER:
Severe burns caused by contact with
hot surfaces
Components heated up by engine
operation or external influences, e.g.
engine parts, the exhaust system,
hydraulic system etc. can cause severe
burns on contact.
Maintain an adequate distance from
hot components. If work has to be
performed on these components,
allow them to cool down first. Wear
safety gloves if necessary.

1. Tractor

1-10

FENDT 700 Vario S4

X990.005.538.013

Содержание FENDT 700 Vario S4 Series




















































Отзывы: