Afag 50315434 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 66

background image

Operating instructions EN

◼

SE-24

◼

01.06.2022

◼

V1.5

51

–66

9.2 Dynamic current limitation

This function is for protecting the motor against overheating and is primarily necessary for motors without temperature sensor.
For motors with temperat

ure sensors (PTC, KTY, etc.) it’s optional.

The dynamic I*t

– current limitation limits the desired current value range of the controller depending the actual motor current and the

time. This function is monitoring the value of the peak current for both the positive and the negative rotating direction. How long the peak
current Ip (CURR_DynLimitPeak) can flow, is conditioned by the parameter tp (CURR_DynLimitTime). After this time the motor current
decreases to the continuous current Ic (CURR_DynLimitCont). This is only valid, if the current was limited to the peak current Ip
(CURR_DynLimitPeak) all the time. If the current was less than the peak current, the time tp (CURR_DynLimitTime) increases
accordantly.

A higher motor current then the continuous current is not allowed till the actual motor current was under the continuous current Ic
(CURR_DynLimitCont). The longer the motor current was under the continuous current Ic (CURR_DynLimitCont) and the lower it was,
that higher would be the allowed temporary motor current, meanwhile the peak current Ip (CURR_DynLimitPeak) keeps limited.

Figure 21: Dynamic current limitation

«
...
49
50
51
52
53
...
»

Содержание 50315434



































































Отзывы:

Нет отзывов

Похожие инструкции для 50315434

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: ZIMO Страницы: 38

Бренд: D+H Страницы: 14

Бренд: Lattice Semiconductor Страницы: 26

Бренд: Datavideo Страницы: 17

Бренд: Datamax Страницы: 22

Бренд: Samson Страницы: 32

Бренд: Quantum Страницы: 15

Бренд: Saga Страницы: 9

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: OBaby Страницы: 7

Бренд: Jäger Страницы: 50

Бренд: Fox Страницы: 5

Бренд: Nice Страницы: 120

Бренд: Seneca Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды