AFA Stainless AFLZ01C Скачать руководство пользователя страница 23

23

– Please ensure that the surface of your AFA product has cooled down before cleaning (clean at room temperature). 
– Use a soft cloth (e.g. a micro fibre cloth) to dry the product after every use. 
– Do not use abrasive cleaning agents or tools – No scratching of the surface.
– Descaling is an aggressive process for products, so you should only do this when and where it is needed. Please wash the 

product thoroughly with clean water after using any cleaning chemicals, then dry it with a soft cloth (e.g. a micro fiber 
cloth). 

– Do not use acidic or caustic cleaning agents or abrasive sponges.
– Do not use degreasing agents or too much cleaning agent.
– Do not spray directly onto the faucet.
– Do not use hard cleaning tools or materials.
– No scratching of the surface.

CLEANING AND CARE INSTRUCTIONS

LIFETIME LIMITED WARRANTY

AFA Stainless LLC warrants its products to be free of defects in material and workmanship during normal residential use for 
as long as the original consumer purchaser owns his or her home. This warranty applies only to AFA Stainless products 
installed in the USA. If a defect is found in normal residential use, AFA Stainless will, at its election, repair, replace or make 
appropriate adjustment. Scratching, staining, acid or alkaline etching of the finish over time due to use, cleaning practices or 
water or atmospheric conditions, are not manufacturing defects but are indicative of normal wear and tear, and are not 
covered under this warranty. Damage caused by accident, misuse, or abuse, such as dents and scratches after installation, is 
not covered by this warranty. Improper care and cleaning will void the warranty. Proof of purchase (original sales receipt) 
must be provided to AFA Stainless with all warranty claims. AFA Stainless is not responsible for labor charges, installation, or 
other  incidental  or  consequential  costs.  In  no  event  shall  the  liability  of  AFA  Stainless  exceed  the  purchase  price  of  the 
product.  If  AFA  Stainless  products  are  used  commercially  AFA  Stainless  warrants  its  products  to  be  free  from  defects  in 
material and workmanship for five (5) years from the date of purchase, with all other terms of this warranty applying except 
duration. If you believe that you have a warranty claim, please contact the AFA Stainless Customer Care Hotline at 877-778-
6888. or by writing to the address shown below. 

AFA USA LLC
Attn: Customer Care
3190 Airport Loop Dr Ste B1, Costa Mesa, CA 92626

Proof of purchase (original sales receipt) from the original consumer purchaser must accompany all warranty claims. Defects 
or damage caused by the use of other than genuine AFA Stainless parts are not covered by this warranty. AFA STAINLESS 
LLC AND/OR SELLER ARE PROVIDING THIS WARRANTY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, 
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE.  AFA  STAINLESS  LLC.  AND/OR  SELLER  DISCLAIMS  ANY  LIABILITY  FOR  SPECIAL,  INCIDENTAL,  OR 
CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty lasts or the 
exclusion or limitation of such damages, so these limitations, and exclusions may not apply to you. This warranty gives the 
consumer specific legal rights. You may also have other rights that vary from state/province to state/province. This warranty is 
to the original consumer purchaser only, and excludes product damage due to installation error, product abuse, or product 
misuse,  whether  performed  by  a  contractor,  Service  Company  or  the  consumer.  This  is  AFA  Stainless  exclusive  written 
warranty. Manufacturers’ warranties may not apply in all cases, depending on factors such as use of the product, where the 
product was purchased, or to whom you purchased the product from. Please review the warranty carefully, and contact the 
AFA Stainless Customer Service Hotline if you have any questions.

Содержание AFLZ01C
























Отзывы: