M
ID
CODE
1
03-0801
03-08021
03-08022
2
03-08023
03-08024
3
03-0803
4
03-0804
5
03-0805
6
03-0806
7
03-0807
03-08081
03-08082
8
03-08083
03-08084
9
03-0809
REPLACEMENT PARTS
B
E
G
H
I
T
.,>
-
m
2
3 4
5
l
8:= I
8:= I
8:= I
�I
DESCRIPTION
Tenninal Box
MotorSMP75
Motor SMP100
Motor SMP120
Motor SMP150
Bolt M6 X30
Washer06
Pump Casing
0-Ring D180 X 6.3
Mechanical Seal
lmp�ler SMP75
lmp�ler SMP100
lmp�ler SMP120
lmp�ler SMP150
Oriented Impeller
0
7
Qty
1
1
1
1
1
6
6
1
1
1
1
1
1
1
1
4
ID
A
C
D
E
F
G
H
I
J
L
M
N
0
CODE
DESCRIPTION
01-05
1.5" Valve
01-0126
O'ring
01-0127
Pressure Gauge
01-0120
Sight glass O'ring
02-0901
O'ring, lid
02-09046
Center Pipe 0350
02-09041
Center Pipe 0400
02-09042
Center Pipe 0450
02-09043
Center Pipe 0500
01-0505
Clamp
02-10066
Filter body 0350
02-10061
Filter body 0400
02-10062
Filter body 0450
02-10063
Filter body 0500
02-0107
Lateral Assembly
02-0111
Drain
02-0112
Positioning pillar
04-0101
Filter Support Stand 0350-0450
04-0102
Filter Support Stand 0500
02-0109
Support pipe
02-0108
Lateral
02-1407
Hose
03-080
Pump
15�
14
-.::::::-;;....
16
��
17
18
12
13
QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
14
9
12
J��
11
10
�
23
�"@
ID
CODE
10
03-0810
11
03-0811
12
03-0812
13
03-0813
14
03-0814
15
03-0815
16
03-0816
17
03-0817
18
03-0818
19
03-0819
20
03-0820
21
03-0821
22
03-0804
23
03-0822
24
03-0823
22----1 'l}----21
7§%
DESCRIPTION
0-Ring D70 X d58
Pump Body
0-Ring D55 X 3.5
Adaptor
Nut
Press Cover
Transparent Cover
0-Ring D130 X 6
Filter
Discharge Nut
0-Ring D16 X 2.4
Bolt M6 X 15
Washer06
Base
Block Gine
r,
20 19
Qty
1
1
2
2
2
1
1
1
1
2
2
2
2
1
1
REMORA
PLASTIC SAND FILTER WITH
PUMP COMBO
OWNER'S MANUAL
Your
sand filter is a high performance, totally corrosion proof filter that blends superior flow characteristics and
features with ease of operation. It represents the very latest in high-rate sand filter technology. It is virtually foolproof in design
and operation. When installed, operated and maintained according to instructions, your filter will produce clear, sparkling water
with minimal attention and care.
HOW IT WORKS
Your filter uses special filter sand to remove dirt particles
from pool water. The filter sand is loaded into the filter tank
and functions as the permanent dirt removing media. The pool
water, which contains suspended dirt particles, is pumped
through your piping system and is automatically directed by
the patented filter control valve to the top of the filter tank. As
the pool water is pumped through the filter sand, dirt particles
are trapped by the sand bed, and filtered out. The cleaned
pool water is returned from the bottom of the filter tank,
through the control valve and back to the pool through the
piping system.
This entire sequence is continuous and
automatic and provides for total recirculating of pool water
through your filter and piping system.
After a period of time, the accumulated dirt in the filter
causes a resistance to flow, and the flow diminishes and the
pressure gauge rises. This means it is time to clean
(backwash) your filter. With the control valve in the backwash
position, the water flow is automatically reversed through the
filter so that is directed to the bottom of the tank, up through
the sand, flushing the previously trapped dirt and debris out
the waste line. Once the filter is backwashed (cleaned) of dirt,
the control valve is manually positioned to Rinse, and then
positioned to Filter to resume normal operation.
INSTALLATION
Only simple tools (screwdriver and wrenches), plus pipe
sealant for plastic adapters, are required to install and/or
service filter.
1. The filter system must be placed on level, very firm,
ground. Position the filter so that the piping connections,
control valve and winter drain are convenient and accessible
for operation, service and winterizing.
2. Assemble the Pump to the platform base. The adapters
must now be installed to connect the pump/filter system.
a. Apply Teflon pipe sealant tape or Permatex No. 2
sealant to straight adapter. Screw adapter into pump
discharge port. (Do not over tighten.)
b. Apply Teflon pipe sealant tape or Permatex No. 2
sealant to elbow adapter. Screw adapter securely into
opening in control valve marked PUMP (Do not over
tighten.)
3. Loading sand media. Filter sand media is loaded through
the top opening of the filter.
a. Loosen flange clamp and remove Filter Control Valve
(if previously installed).
b. Cap internal pipe with sand shield to prevent sand from
entering it. Be sure pipe is securely in place in bottom
under drain hub.
c. We recommend filling tank approximately 1/2 way with
water to provide a cushioning effect when the filter
sand is poured in. This helps protect the under drain
laterals from excessive shock. (Be sure the winter
drain cap is securely in place on drain pipe.)
Note:
Check to confirm all laterals are in the down position
before loading with sand. (See Figure A on Page 2.)
d. Carefully pour in correct amount and grade of filter
sand, as specified. (Be sure center pipe remains
centered in opening.) Sand surface should be leveled
and should come to about the middle of the filter tank.
Remove sand shield from internal pipe.
4. Assemble Filter Control Valve to filter tank.
a. Place valve flange clamp around neck of tank. Do not
tighten. Wipe filter flange clean.
b. Insert Filter Control Valve (with valve/flange O-ring in
place) into the tank neck, taking care that the center
pipe slips into the hole in the bottom of the valve.
Place clamp around valve flange and tank flange just
enough so that the valve may be rotated on tank for
final positioning.
REMORA
SALES AND SERVICE 01842 819130
Suitable for above-ground pools only - pump not self-priming