manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 36

36

Chapter 2

www.aerotech.com

2.3.1.2. Unpowered Motor and Feedback Phasing

Disconnect the motor from the controller and connect the motor in the test configuration shown in

Figure 2-

10

. This method will require a two-channel oscilloscope, a 5V power supply, and six resistors (10,000 ohm,

1/4 watt). All measurements should be made with the probe common of each channel of the oscilloscope
connected to a neutral reference test point (TP4, shown in

Figure 2-10

). Wave forms are shown while moving

the motor in the positive direction.

Figure 2-10:

Motor Phasing Oscilloscope Example

With the designations of the motor and Hall leads of a third party motor determined, the motor can now be
connected to an Aerotech system. Connect motor lead A to motor connector A, motor lead B to motor
connector B, and motor lead C to motor connector C. Hall leads should also be connected to their respective
feedback connector pins (Hall A lead to the Hall A feedback pin, Hall B to Hall B, and Hall C to Hall C). The
motor is correctly phased when the Hall states align with the Back EMF as shown in (

Figure 2-11

). Use the

CommutationOffset parameter to correct for Hall signal misalignment.

Figure 2-11:

Brushless Motor Phasing Goal

Ndrive ML

Installation and Configuration

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды