Aerotech HexGen HEX300-230HL Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 44

background image

Tightening torque values for the mounting hardware are dependent on the properties of the surface
to which the stage is being mounted. Values provided in

are typical values and may not be

accurate for your mounting surface. Refer to

for specific model mounting locations and

dimensions.

Table 2-1:

Stage to Mounting Surface Hardware

Mounting Hardware

Typical Screw Torque

M6 or 1/4-20 SHCS (3 places)

7 N·m

Figure 2-3:

Mounting Hole Locations

HEX300-230HL Hardware
Manual

2.3. Securing the Hexapod to the Mounting

Surface

www.aerotech.com

21

«
...
19
20
21
22
23
...
»

Содержание HexGen HEX300-230HL













































Отзывы:

Нет отзывов

Похожие инструкции для HexGen HEX300-230HL

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: FagronLab Страницы: 16

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

Бренд: K&K Страницы: 8

Бренд: made for movement Страницы: 51

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: GE Страницы: 212

Бренд: Gainsborough Страницы: 2

Бренд: Gainsborough Страницы: 2

Бренд: Gait up Страницы: 12

Бренд: Gait up Страницы: 6

Бренд: Gaiam Страницы: 2

Бренд: Jet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды