Aerotech BL 10-40 Скачать руководство пользователя страница 35

Страница: 35 / 68

Installation and Configuration

Disconnect the motor from the controller and connect the motor in the test configuration shown in Figure 2-

12. This method will require a two-channel oscilloscope, a 5V power supply, and six resistors (10,000 ohm,

1/4 watt). All measurements should be made with the probe common of each channel of the oscilloscope

connected to a neutral reference test point (TP4, shown in Figure 2-12).

To determine the relative phasing/order of the three motor lead signals in relation to each other, connect chan-

nel 1 of the oscilloscope to TP1. Connect channel 2 to TP2 and move the motor in the positive direction

(CW) by hand. Note the peak of the sine wave signal of channel 1 in comparison to the peak of the sine wave

signal of channel 2. Next, disconnect channel 2 from TP2 and reconnect it to TP3 and again move the motor

in the positive direction. Note the peak of the sine wave signal of channel 3 in comparison to the peak of the

sine wave signal of channel 1.

Aerotech phasing configuration expects ØC to be the lead signal (in time), ØB to follow it, and ØA to follow

ØB. This means that whichever signal has its sine wave peak farthest to the left should be designated as the

ØC signal.

Figure 2-12:

Motor Phasing Oscilloscope Example

www.aerotech.com

Chapter 2

Содержание BL 10-40





































































Результаты поиска

Содержание BL 10-40

Отзывы:

Бренды по названию

Популярные бренды

Aerotech BL 10-40, Руководство по оборудованию

Результаты поиска

Содержание BL 10-40

Отзывы:

Бренды по названию

Популярные бренды