manualshive.com logo in svg

Aerotech Automation1 XL5e, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XL5e Скачать руководство пользователя страница 62

2.5.2. Position Synchronized Output (PSO)

The PSO signal is available on the dual-function AUX Marker/PSO signal lines. Use the PSO pulse external
sync functions to configure the auxiliary marker as an output. Refer to the Help file for more
information.

Use the PsoOutputConfigureOutput() function to transmit the PSO output signal on the Marker ± pins
differentially. Or, use the PsoOutputConfigureOutput() function to configure the Marker - pin as a
5V TTL PSO output.

The differential signal format is recommended when using long cable lengths in noisy environments or
when high frequency pulse transmission is required. It is best to locate the line receiver close to the
receiving electronics. A 5 V TTL signal is used to drive an opto coupler or general purpose TTL input. This
signal is active high and is driven to 5 V when a PSO fire event occurs. When the drive is reset or after
initial power up, the PSO pins (refer to

Table 2-38

), are not actively driven and the fail safe state is

defined by pull-up and pull-down resistors as shown in

Figure 2-32

.

The -EB1 I/O option board has additional PSO signal formats. Refer to

Section 3.5.

for more information.

Table 2-37:

PSO Specifications

Specification

Value

Output

TTL

5 V, 16 mA (max)

Maximum PSO Output (Fire) Frequency

TTL

12.5 MHz

RS-422

12.5 MHz

Output Latency
[Fire event to output change]

TTL

15 ns

RS-422

15 ns

Table 2-38:

PSO Pins on the Auxiliary I/O Connector

Pin#

Description

In/Out/Bi

19

Auxiliary Marker- / PSO output / TTL Output

Bidirectional

20

Auxiliary  / PSO output

Bidirectional

21

Common

N/A

2.5. Auxiliary I/O Connector

XL5e Hardware Manual

62

www.aerotech.com

Содержание Automation1 XL5e















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды