manualshive.com logo in svg

Aerotech Automation1 XL5e, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XL5e Скачать руководство пользователя страница 35

2.2.3.1. Stepper Motor Phasing

A stepper motor can be run with or without an encoder.

Without an Encoder:

You do not need to phase the motor.

With an Encoder:

Because the end of travel (EOT) limit inputs are relative to motor rotation,

it is important to phase the motor.

Run a positive motion command. The motor is phased correctly if there is a positive scaling factor
(determined by the CountsPerUnit parameters) and the motor moves in a clockwise direction when you
view the motor from the front mounting flange (

Figure 2-12

). If the motor moves in a counterclockwise

direction, swap the motor leads and re-run the command. After the motor has been phased, if you want
to change the direction of positive motion, use the ReverseMotionDirection parameter.

Figure 2-12:

Positive Motor Direction

For Aerotech-supplied systems, the motor, encoder and Hall sensors are correctly configured and
connection adjustments are not necessary.

www.aerotech.com

35

XL5e Hardware Manual

2.2.3. Stepper Motor Connections

Содержание Automation1 XL5e















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды