manualshive.com logo in svg

Aerotech Automation1 XC6e Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC6e Series Скачать руководство пользователя страница 32

2.2.1. Brushless Motor Connections

The configuration shown in

Figure 2-3

is an example of a typical brushless motor connection.

Figure 2-3:

Brushless Motor Configuration

Table 2-8:

Wire Colors for Aerotech-Supplied Brushless Motor Cables 

Pin

Wire Color Set 1

(1)

Wire Color Set 2

Wire Color Set 3

Wire Color Set 4

Green/Yellow &

Shield

(2)

Green/Yellow &

Shield

Green/Yellow &

Shield

Green/Yellow &

Shield

A

Black

Blue & Yellow

Black #1

Black & Brown

B

Red

Red & Orange

Black #2

Red & Orange

C

White

White & Brown

Black #3

Violet & Blue

(1) Wire Color Set #1 is the wire set typically used by Aerotech.
(2) “&” indicates two wires (Red & Orange); “ / ” indicates a single wire (Green/White).

Brushless motors are commutated electronically by the controller. The use of Hall effect devices for
commutation is recommended.

The controller requires that the Back-EMF of each motor phase be aligned with the corresponding Hall-
effect signal. To ensure proper alignment, motor, Hall, and encoder connections should be verified using
one of the following methods:

powered

, through the use of a test program; or

unpowered

using an

oscilloscope. Both methods will identify the A, B, and C Hall/motor lead sets and indicate the correct
connections to the controller. Refer to

Section 2.2.1.1.

for powered motor phasing or

Section 2.2.1.2.

for unpowered motor and feedback phasing.

For Aerotech-supplied systems, the motor, encoder and Hall sensors are correctly configured and
connection adjustments are not necessary.

A motor filter module can be installed between the drive and the motor to reduce the effects on
PWM generated noise currents.

2.2.1. Brushless Motor Connections

XC6e Hardware Manual

32

www.aerotech.com

Содержание Automation1 XC6e Series















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды