Aerotech Automation1 XC4e Скачать руководство пользователя страница 62

Страница: 62 / 122

2.4.1. STO Standards

Table 2-28

describes and specifies the safety requirements at the system level for the Safe Torque Off

(STO) feature of the XC4e. This assumes that diagnostic testing is performed according to

Section 2.4.4.

and

Table 2-29

Table 2-28:

STO Standards

Standard

Maximum Achievable Safety

EN/IEC 61800-5- 2:2016

SIL 3

EN/IEC 61508-1:2010

SIL 3

EN/IEC 61508-2:2010

SIL 3

EN ISO 13849-1:2015

Category 4, PL e

EN/IEC 62061:2005 with Amendments

SIL 3

Table 2-29:

STO Standards Data

Standard

Value

EN ISO 13849-1:2015

MTTF

> 1000 years,

AVG

99%

Maximum PL e, Category 4

EN ISO 13849-1:2015
EN/IEC 61508

Lifetime = 20 years
No proof test required
Interval for manual STO test:

Once per year for SIL2/PL d/category 3

Once per three months for SIL3/PL e/category 3

Once per day for SIL3/PL e/category 4

EN/IEC 61508

SIL3
PFH < 3 FIT
SFF > 99%

2.4. Safe Torque Off Input (STO)

XC4e Hardware Manual

www.aerotech.com

Содержание Automation1 XC4e



























































































































Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Automation1 XC4e, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды