manualshive.com logo in svg

Aerotech Automation1 XC4e, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC4e Скачать руководство пользователя страница 18

Table 1-1:

Features and Options

Standard Features

l

100-240 VAC control supply inputs

Section 2.1.1.

l

0-240 VAC motor supply inputs (producing 340 VDC)

Section 2.1.2.

l

Line driver square wave quadrature encoder input for position and velocity feedback

Section 2.3.1.

l

Absolute Encoder support on the Feedback Connector

Section 2.3.1.2.

l

One fail-safe brake output

Section 2.3.6.

l

Two STO sense inputs

Section 2.4.

l

Line driver square wave auxiliary quadrature encoder input or output for PSO 

Section 2.5.1.

l

Absolute Encoder support on the Auxiliary I/O Connector

Section 2.5.1.2.

l

Four digital user outputs

Section 2.5.3.

l

Six digital user inputs

n

Four Digital Inputs

Section 2.5.4.

n

Two High-Speed Inputs

Section 2.5.5.

l

One 16-bit analog output (±10 V)

Section 2.5.6.

l

One 16-bit differential analog input (± 10 V)

Section 2.5.7.

Options

Peak Current

Section 1.1.

-10

10 A Peak, 5 A Continuous Current

-20

20 A Peak, 10 A Continuous Current

-30

30 A Peak, 10 A Continuous Current

Expansion Board

Chapter 3

-EB0

No expansion board

-EB1

I/O expansion board

l

Three 16-bit analog outputs (±10 V)

l

Three 16-bit differential analog inputs (±10 V)

l

16 digital logic inputs (5 - 24 VDC); connect to current sourcing or sinking devices

l

16 digital logic outputs (5 - 24 VDC); user defined as current sourcing or sinking

l

Digital logic laser firing (PSO) output

Multiplier

Section 2.3.1.3.

-MX0

No encoder multiplier

-MX2

Interpolation circuit allowing for analog sine wave input on the primary encoder channel with
an interpolation factor of 65,536.

-MX3

Interpolation circuit allowing for analog sine wave input on the primary encoder channel with
an interpolation factor of 65,536 and an auxiliary encoder channel with an interpolation factor
of 16,384.

PSO

Section 2.5.2.

-PSO1

One-axis PSO firing (includes One-axis Part-Speed PSO)

-PSO2

Two-axis PSO firing (includes Two-axis Part-Speed PSO)

-PSO3

Three-axis PSO firing (includes Three-axis Part-Speed PSO)

-PSO5

Two-axis Part-Speed PSO firing, which uses the PSO firing circuit based off of the commanded
vector velocity of up to 2 axes (includes One-Axis PSO).

-PSO6

Three-axis Part-Speed PSO firing, which uses the PSO firing circuit based off of the commanded
vector velocity of 3 or more axes (includes One-Axis PSO).

External Shunt

Section 2.8.

-SX0

No connector for the External Shunt

-SX1

Connection provided for an external shunt resistor network

Version

-DEFAULT

Firmware Matches Software Line

-LEGACY

Legacy Firmware Version X.XX.XXX

Chapter 1: Introduction

XC4e Hardware Manual

18

www.aerotech.com

Содержание Automation1 XC4e



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды