manualshive.com logo in svg

Aerotech Automation1 XC4e, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC4e Скачать руководство пользователя страница 74

2.5.3. Digital Outputs

Optically-isolated solid-state relays drive the digital outputs. You can connect the digital outputs in
current sourcing or current sinking mode but you must connect all four outputs in the same
configuration. Refer to

Figure 2-40

and

Figure 2-41

.

You must install suppression diodes on digital outputs that drive relays or other inductive devices. To see
an example of a current sourcing output that has diode suppression, refer to

Figure 2-40

. To see an

example of a current sinking output that has diode suppression, refer to

Figure 2-41

The digital outputs are not designed for high-voltage isolation applications and they should only be used
with ground-referenced circuits.

The digital outputs have overload protection. They will resume normal operation when the overload is
removed.

Table 2-40:

Digital Output Specifications

Digital Output Specifications

Value

Maximum Voltage

24 V (26 V Maximum)

Maximum Sink/Source Current

250 mA/output

Output Saturation Voltage

0.9 V at maximum current

Output Resistance

3.7 Ω

Rise / Fall Time

250 µs (2K pull up to 24V)

Reset State

Output Off (High Impedance State)

Table 2-41:

Digital Output Pins on the Auxiliary I/O Connector

Pin#

Description

In/Out/Bi

7

Digital Output 0

Output

8

Digital Output 1

Output

9

Digital Output 2

Output

15

Digital Output Common

N/A

16

Digital Output 3

Output

2.5. Auxiliary I/O Connector

XC4e Hardware Manual

74

www.aerotech.com

Содержание Automation1 XC4e



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды