background image

EGT-100 Exhaust Gas Temperature Indicator 

Page 1 of 11

 

 

Aerospace Logic Inc. 

3150 Ridgeway Drive, Unit #43, Mississauga, Ontario, L5L 5R5, CANADA 

Tel. (905) 569-3887 | Fax. (416) 352-5854 | Email. [email protected] 

www.aerospacelogic.com 

EGT-100 Operations & Installation Manual – Ver. 1.9 – June 5, 2003 

 

 

 

 

All specification subject to change 

© 2002-2003 Aerospace Logic Inc.

 

 
 

EGT-100 Operations and Installation Manual 

 
 
 
 
 
 
 
 
 
 
 
 
 

READ THIS FIRST

 

 
 

Congratulations on the purchase of your EGT-100 Exhaust Gas Temperature Indicator. 
This instrument is a complex precision instrument manufactured to exceed Airborne 
Equipment Standards DO-160D, DO-178B and TSO C43c standards. In order for your 
instrument to function correctly you will need to review the instructions in this brief 
manual. 
 
 
This document covers the following instrument models: 
 

  EGT-100-4 

4 Cylinder EGT 

  EGT-100-4V  4 Cylinder EGT with Voltmeter 

  EGT-100-6 

6 Cylinder EGT 

  EGT-100-6V  6 Cylinder EGT with Voltmeter 

This manual is certified for use with 

instrument serial number  

 

ASL000000 

 

Use of this manual with any other 

instrument voids all warranties and may 

result in damage to the instrument 

Содержание EGT-100 Series












Отзывы: