background image

Please read and be sure you thoroughly understand this manual before installing your 
tail. Be sure you are thoroughly familiar with the tail and the contents of this manual 
before initial operation. 
 
It is important that you visit us regularly at 

http://www.aeros.com.ua

 

 
In case of any doubts or questions contact your local dealers or Aeros. 
 
We wish you a safe and enjoyable flying career. 
 
   Aeros Ltd. 
 
 
 
 
 
 
 
DEFINITIONS 
 
Definitions used in this Manual such as WARNING, CAUTION and NOTE are employed 
in the following context: 
 

WARNING: 

OPERATING PROCEDURES, TECHNIQUES, ETC. WHICH IF NOT 

FOLLOWED CORRECTLY, MAY RESULT IN PERSONAL INJURY OR DEATH. 
 

CAUTION: 

OPERATING PROCEDURES, TECHNIQUES, ETC. WHICH IF NOT 

STRICTLY OBSERVED, MAY RESULT IN DAMAGE TO THE AIRCRAFT OR ITS 
INSTALLED EQUIPMENT 
 

NOTE: 

Operating procedures, techniques, etc. which considered essential to highlight. 

 
 
    

 

 
 
 
CONTENTS 
 

                                                                                                                              
1.  General Information                                                                                              3 

 

2.  Technical Information                                                                                            3 

 

3.  Tail Installation                                                                                                      3 

 

4.  Glider Adjustments                                                                                                7 

 

5.  Maintenance and Storage                                                                                     7 

 
 

 

2

Содержание Combat 09 13.7









Отзывы: