manualshive.com logo in svg

Aeroqual 930 Series, Руководство пользователя, Страница: 10 / 19

Поделиться
Скачать
Aeroqual 930 Series Скачать руководство пользователя страница 10

 

Page | 10  

Aeroqual Series 930 User Guide 

6. Troubleshooting 

 

Fault Description 

Possible Cause 

Remedy 

No Power 

Power connection broken 

Power supply failure 

S930 damaged 

Reconnect power cable 

Replace 24V power supply 

Replace unit 

RS485 communications 

unstable 

RS485/RS232 adaptor faulty 

Connections broken 

ID incorrect 

Noise on cable 

Sensor head not fitted correctly 

Reconfigure/replace adaptor 

Reconnect leads 

Check ID 

Use shielded twisted pair cable 

Insert head correctly 

4-20mA output failure 

30V input exceeded 

Replace S930 

Network unstable 

ID conflict 

 
Noise on cable 

Jumpers set incorrectly 

930 units too close together 

Modify IDs so that no S930 units share 
the same ID 

Use shielded twisted pair cable 

Set jumpers correctly 

The cables between the S930 units 
should be a minimum of 30 cm in length 

If connected to a display: 

 

Display shows -1 

 
 

 

Display shows 1 

 
 

Display shows -.125 

 

Display oscillated between 

min and max 

 
 
Over-range (>20mA) reverse 
loop current 
 

 
Over-range loop current (>20 
mA) 
 
4-20mA loop not powered 
 

Sensor head not fitted correctly 

 
 
Loop polarity is incorrect. Reverse the 
polarity. Incorrect loop polarity can cause 
irreversible damage to the 930 unit 
 
 
Reduce loop current  
 
 
Power loop. The display requires the 
loop to be powered to read correctly 

Insert sensor correctly 

Sensor failure when new 

sensor connected 

Insufficient warm-up 

Air contaminated 

 
Sensor damaged 

Run the sensor for 24-48 hours 

Move the sensor to cleaner environment 
and check reading 

Replace sensor 

 

Sensor showing high 

baseline reading under 

zero gas conditions 

Background gas level higher 
than normal 

Interference gas present 

 
Sensor zero drift 
 

Sensor damaged 

Move sensor to clean environment and 
recheck baseline 

Move sensor to clean environment and 
recheck baseline 

Rezero sensor in a clean, stable 
environment 

Replace sensor 

Sensor showing higher 

than expected reading in 

the presence of sensor 

gas 

Zero calibration incorrect 

Span calibration incorrect 

Interference gas present 

 
 
Sensor calibration lost 

Zero calibrate sensor 

Span calibrate sensor 

Move sensor to clean environment and 
check reading upon exposure to know 
concentration of gas 

Replace sensor 

 

Содержание 930 Series




















Отзывы:

Нет отзывов